Heatflex Cables Private Limited

Submersible 3 Core Flat Cables are manufactured keeping in mind the severe and difficult conditions in which they are required to perform. The area of installation is physically restrictive, and the environment is very hostile.

These are used to connect submersible pump motor with supply lines. The slot available in the tube well being narrow the shape of the cables has to be suited for such an application.

Features:-

• Excellent resistance to water, moisture, abrasion, grease and oil
• Longer flex life
• Excellent mechanical & electrical properties

Application:- Connect submersible pump motor with supply lines

Description:- 1100 V Grade annealed bare electrolytic high conductivity multi stranded copper conductor polyethylene coated, PVC insulated and overall matt finish sheathed flat 3 core waterproof and weatherproof submersible cables as per IS : 694 / 1990.

Range : 1.5 sq mm to 120 sq mm

Application:

• In electricity theft prone areas.
• As replacement of bare lines in rural are & narrow street with limited space.
• As replacement of bare lines where reliabilities of support is of prime importance.
• In hilly terrain here cost of erection of overhead lines or under ground cable becomes very high.
• As reinforcement of existing system with increase in voltage/current carrying capacity.
• For temporary supplies.

The PVC LT Power Cables are installed in residential buildings, commercial buildings, communication panel systems and other electrical installations. Our cables are not affected by vibration and are proven to be highly durable. The PVC, we use in our power cables enhance the life of wires and is perfect for power supply. It is available in several standard as well as customized configurations to meet the requirements of clients.

Features:

• High on Current Rating
• High on Overload Capacity
• High on Short Circuit Rating
• Light in Weight with small Bending Radius
• Lower Di-electric Constant & Power Factor
• Better Impact, Abrasion, Corrosion Resistance
• Easy to join and terminate
• Non-hygroscopic insulation unaffected by moisture
• Non-migration of compound permitting vertical installation
• Good ageing properties
• Unaffected by vibration

These Cables are designed to carry communication and control signal in a variety of installation types including those found in the petrochemical industry. The signals can be of analogue data or voice type and from a variety of transducers such as pressure, proximity or microphone. Collectively and individually screened pairs are available within the range where further signal security is required. Unique Instrumental cable offers total interference free data transfer in measuring process control & security systems. Instrumentation process in any industry is a very important factor for controlling various parameters during process. Microprocessor based control devices demand very low noise level & attenuation of signals in the cable. The calls for careful designing & manufacturing of cables with stringent quality control.

Unique make signal cables, Annealed Bare/Tinned copper conductor, PVC insulated and sheathed, shielded with Aluminium backed mylar taped with Annealed tinned copper conductor drain wire in continues contact with aluminum side of tape, instrumentation Armoured/Unarmoured Cable conforming to BS:5308/II/1986&IS:1554/Part-I/1988.

RANGE: 0.2 sq.mm to 2.5 sq. mm in cores, pairs, Triads & quads.

Application:- A shielded cable is an electrical cable of one or more insulated conductors enclosed by a common conductive layer. The shield may be composed of braided strands of copper or aluminum mylar tape, or a layer of conducting polymer. Usually, this shield is covered with a jacket.

The shield acts as a Faraday cage to reduce electrical noise from affecting the signals, and to reduce electromagnetic radiation that may interfere with other devices (see electromagnetic interference).

The shield minimizes capacitive coupled noise from other electrical sources. The shield must be applied across cable splices. In shielded signal cables the shield may act as the return path for the signal, or may act as screening only.

Description:- The annealed tinned/bare Electrolytic high conductivity copper multi strand flexible conductor as per IS: 8130/1984 of class-5, PVC insulated as per IS: 5831/1984, cores twisted together, Melinex taped. Shielded with aluminium mylar taped and screened with tinned copper braiding, taped again & overall PVC sheathed as per BS 5308 Part-2 multi core instrumentation Shielded Flexible cable

Range:- 0.2 sq.mm to 150 sq.mm (single core & multicore)